← Back to the catalog

Learn to Knit: Cast On, Knit, Purl and Make Your First Scarf

Learn to knit from zero: cast on with the long-tail method, knit and purl, read a simple pattern, rescue a dropped stitch, then bind off, weave in ends and block. You'll start a garter scarf on day one and have every skill to finish it.

Language
English
Lessons
6
Minutes
150

Price: · The subscription includes the whole catalog at no extra cost.

Course outline

  1. The Two Stitches: Cast On, Knit and Purl

    1. Long-Tail Cast On: Your First 20 Stitches (25′)
    2. The Knit Stitch and Even Tension (25′)
    3. Purl, and Combining Knit and Purl (25′)
  2. Patterns, Fixes and Finishing Your Scarf

    1. Fixing a Dropped Stitch Before It Runs (25′)
    2. Reading a Simple Pattern, and Writing Yours (25′)
    3. Bind Off, Weave In Ends, Finish the Scarf (25′)

Free first lesson

Long-Tail Cast On: Your First 20 Stitches

Two strands, one row of loops

Your scarf begins before the first knit stitch: it begins with a row of loops on the needle, and putting them there is called casting on. The method you'll use, the long-tail cast on, needs both ends of the yarn at once: the loose end (the tail) and the end still attached to the ball (the ball strand). Each loop takes yarn from the tail while the ball strand locks it in place, so the tail gets shorter with every stitch. That is the one thing about this method you cannot fix halfway: the tail must be long enough before the first loop.

It earns its place on a scarf: the edge it makes is firm yet stretchy, so the end of the scarf neither flares nor pinches. And if you're unsure which end is which, follow each one — the ball strand leads back to the ball; the tail leads to nothing.

Why must you know which strand is which before you begin?

Your first 20 stitches

Because each loop eats tail: guess the length wrong and the loops simply stop mid-row, with no way to add yarn without a knot in your edge. So the tail comes first.

Estimate the tail
  1. Wrap the yarn loosely around your needle 20 times — one wrap for each stitch you plan — then add a hand's length for the slip knot and the final tug. Pinch that spot.
  2. At the pinched spot, make a loop of yarn, reach through it, pull a small new loop partway back through, and slide that knot onto your needle. Snug it gently — this slip knot is your first stitch.
Cast on
  1. Hold the needle in your right hand. Lay the tail over your left thumb and the ball strand over your left index finger, then close your remaining fingers over both strands. Your hand forms a slingshot.
  2. Slide the needle tip up through the loop around your thumb, from below.
  3. Swing the tip over the index-finger strand and catch it from above.
  4. Draw the caught strand down through the thumb loop.
  5. Slide your thumb out of its loop, then tug the tail strand just enough to settle the new stitch against the others — it should still slide freely.
  6. Repeat steps 4–7 until you have 20 loops, counting the slip knot. A useful check at stitch 10: roughly half of the wrapped length of tail should be gone; much more, and the tail was short.
  7. Lay the needle flat: even loops look like a row of identical V's. A loop that is slightly smaller evens out in the first knit rows, but if loops fight the needle, loosen your tug, not the yarn.

A cast-on you can read

Cast on a second time for practice, and this time watch what your hands tell you: at stitch 15, the tail is too short to make another loop, and 5 stitches still remain.

Your call: what went wrong, and what do you do next? Decide before reading the answer — then compare it with the folded reference below.

What ruins a cast-on

  • Running out of tail. Every stitch eats tail: estimate the length before tying the slip knot.
  • Strangling the loops. Snug, don't pull tight. If the tip can't slide under a loop, redo it looser — or cast on over two needle tips held together, then slide one needle out before you knit.
  • Forgetting the slip knot in the count. It is stitch 1.

Three things to keep

  • Every stitch eats tail: size the tail before the slip knot.
  • One wrap per stitch, plus a hand's length.
  • Loops snug but sliding; the slip knot is stitch 1.

Cast on your scarf's 20

Cast on your scarf's real 20 stitches — the scarf starts here. In worsted yarn, 20 stitches make a slim scarf about 4 inches (10 cm) wide. Check that every loop slides along the needle and some tail is left, and note how you estimated the tail.

cast on
Putting the first row of loops onto the needle so knitting can begin.
long-tail cast on
A cast-on method that uses both the loose end and the ball end of the yarn at the same time.
tail
The loose end of yarn that is not attached to the ball.
slip knot
An adjustable knot placed on the needle; it counts as the first stitch.
stitch
One loop of yarn held on the needle.